Monthly Archives: August 2017
Kess v2 Slave vs Kess v2 Master
Kess v2 Slave vs Kess v2 Master
Thread: Kess v2 Slave & Master any difference & how to convert
If you have a master version you can work directly on the program you have write on the vehicle (tuning, egr off, ….) and rewrite after directly.
If you are a slave version (who depend of a master (who do modificated), you read the program (crypted by genius), you send it to the master, he do what you what (money paid) and he re-sent to you to write in the ecu machine.It is expensive for the slave version user who depend of a master.
Kess v2 slave into master:
clone kess v2 floods the market is why there is lots of genuine kess slave for sale, plus most slaves cannot do boot mode
the advantages of using original kess v2 and converting it is that you have genuine original kess hardware, so the chances of hardware failure is smaller
if you can fit genuine nxp chip then great, otherwise you will converting to Chinese NXP with the Chinese firmware
advantages are that converted unit does boot mode, and in some cases have more protocols, you already said yourself you want more freedom, and likely better tuning files!
If you’re not equipped with rich tech knowledge & experience, forget it and escape from risk. Just buy a kess v2 china clone master version:
KESS V2 Master V4.036
KESS V2 Master V5.017
2017 CGDI BMW Key Programmer CGDI Prog CAS4 programmer
Tips: The cost for update is 10usd per month after half year.
CGDI Prog BMW MSV80 BMW CGDI Prog Car Key Programmer for BMW CAS1/CAS2/CAS3/CAS3+ Key Matching and All key lost
How to fix CarProg Antenna
About Carprog Antenna Fix:
replaced 150k with 15k (resistor)
2+3+4 here we need to solder a capacitor with aproximately 6-7 nF(put one or combine from 2-3 capacitors)
removed 100 nF capacitor
removed 100 pF capacitor
in position 2 it was a 2.8nF capacitor
in pos 3 it was 0.5 nF cap
in pos 4 it was 100 nF cap
YOU SHOULD HOLD RESPONSIBILITY OF WHAT YOU WILL TRY.
GOOD LUCK!!!!!!
If you fail or nothing work, go for another Carprog 8.21 with a good PCB:
http://www.eobdii.fr/wholesale/carprog-full-perfect-online-version-with-21-adapters.html
SKP1000 Program Nissan Qashqai 2016 Smart Card without BCM code
Nissan Qashqai 2016 smart card key programming is the same as new X-tail. Both has 20-digit BCM code. Original Nissan Qashqai key use special 2-button 315MHz no chip smart key. SKP1000 key programmer will program smart card for this model without BCM code.
(CI600 Plus the Chinese version of SKP1000)
2016 Qashqai BCM Type 284B1-4BY5A is different from X-tail, but they have same immobilizer system
Connect SKP-1000 key programmer with vehicle via OBD socket
Select Immobilizer->Nissan->2013-Nissan X-tail smart card (Auto read BCM code)
Select OBDII connector
Turn Ignition to ON position
Press YES to continue
Configuring the system….
Select Program Smart Card
Turn ignition OFF
Turn on emergency switch (Shown as picture below)
Remove all keys
Maximum 4 keys can be programmed
Press YES to continue
SKP1000 will read BCM code automatically, then start to program smart card. This will delete all smart card.
Press the vehicle engine Start button once
Attach the smart card to the Start button within 5 seconds
Dashboard turns on, immo indicator flashes for 5 times
Press YES to continue
Follow procedure above to program next smart card
VXDIAG VCX NANO FordECU Programming: 100% Success
This is Ford IDS Online Programming Service, incl. how to register an programming account , what kind of Ford diagnostic tool should use and how to use it for Ford ECU programming online. Hope this write-up helps.
I am using VXDIAG VCX NANO Ford, AllScanner
Go to J2534 Programming
Http://www.motorcraftservice.com/ FORD Motorcraft Service
The official site to register my account
Online programming account only
Have good success on 2005 Ford Escape 3.0 V6
PCM programming online zero issues!!!
P.S, tips i followed:
How to do FORD PCM PROGRAMMING:
scope & scan scopes PCM Ford PCM vehicle diagnostics repair shop training technician training automotive aftermarket
Programming Ford electronic control units (ECUs) is pretty straightforward and simple compared to many other OEMs. However, Ford does do one thing differently than most other OEMs. The normal Ford programming procedure has you “inhale” (read and store) the As Built data from the old ECU to the scan tool so that these As Built vehicle specific production and calibration details can then be transferred to a new, remanufactured or salvaged ECU you are installing.
A complication arises when you are attempting to replace an ECU that is dead or not communicating with the scan tool or programming device. In this instance, you are going to have to use a different method of telling the replacement ECU what the needed As Built data information should be. The Ford recommended procedure for this is stated as:
“Programmable Module Installation (PMI) must be performed when replacing module. If the information cannot be inhaled from the original module, As-built data must be used to properly configure module”
This procedure requires purchasing a per use subscription for all ECUs, except the PCM, from the Ford Motorcraft website, http://www.motorcraftservice.com. Once purchased you use the vehicle identification number (VIN) to acquire the As Built data for the particular ECU you are replacing. This As Built data is actually multiple lines of hexadecimal numbers entered into dialogue boxes in the programming software. We will describe this process for Ford ECUs in next month’s column. For this months column we will describe a quicker method than acquiring the As Built hex info to install a replacement powertrain control module (PCM) in a Ford vehicle where the old PCM is damaged and not communicating. All we need do is tell a little white lie to the scan tool or programming device!
To accomplish this trick, connect your Ford diagnostic toolor Flash programming device to the diagnostic link connector (DLC). Leave the ignition key in the OFF position. While the key is off, attempt to connect with the vehicle using your tool’s software. The programming software will show a status bar for 45 seconds while it attempts communication with the vehicle. Of course, the communication attempt will fail because the key is off! It will then ask you to turn the key off and on again as it again attempts to communicate with the vehicle. After this process completes the software will ask you if you want to make another attempt. Choose no to this query.
You are then asked to choose from a list of vehicles to communicate with. Typically, your choice on this page will be “all other” shown on the top of the list as the rest of the list are non-domestic vehicle models
The software will explain that you must provide some numbers from the actual ID label on the old PCM in order for the software to identify the vehicle you intend to communicate with. Use the actual PCM’s label shown here if Figure 1 to gain the information you need. As you can see in screen shot shown in Figure 2, there are three sets of data fields you can use. You need only use one of these data fields to get the job done. I use the Tear Tag number because it is the easiest. In our example, we take the YPZ2 shown on the PCM label in figure 1 and type it into the Tear Tag data field as shown in Figure 2.
The next screen shown will ask you to enter the VIN and mileage. This VIN information is important if your state has an OBDII inspection program requiring a VIN read from the DLC for positive vehicle identification purposes so do not skip this step.
Once the vehicle is properly identified as shown in Figure 3, you can use the normal PCM replace and program procedure. You may be asked to provide a couple of other pieces of information like tire size or whether the vehicle has four-wheel drive or not.
VVDI2 Latest Software V4.2.5 Update Information
VVDI2 Latest Software V4.2.5 Update Information
************************************************************************
*** 2017-08-10
*** Require firmware V4.2.6
************************************************************************
===== VAG V4.2.5 =====
1. Add Polish language support
2. Improvement for flash updating (for frf files)
3. Support decode kessy for Touareg, Bentley, A8, Cayenne, Phaeton after 2008
1). You must read kessy data with VVDI-PROG (version above V4.5.9)(IMMO-VW-Kessy(2008- )
2). Load the file read by VVDI-PROG in vvdi2, you will get the PIN code and 7 bytes CS
3. Bugfix for immo5 lost all key with A6, A7, A8, Touareg
4. Support read A6/Q7 latest J518(4F0910852B H08 0210) with 9S12DT256 module
5. Improvement for “Lost all key via OBDII”
6. Bugfix
===== BMW V4.2.5 =====
1. Add Polish language support
===== Porsche V4.2.5 =====
1. Add Polish language support
===== PSA V4.2.5 =====
1. Add Polish language support
===== Transponder Programmer V4.2.5 =====
1. Add Polish language support
2. Support the latest remote type
3. Immobilizer data tool: bugfix for olvo Trucks FH12(93C66)
4. Immobilizer data tool: bugfix Brilliance Zunchi 93C46
5. Immobilizer data tool: bugfix Fiat Marea 93C46
6. Immobilizer data tool: bugfix BMW CAS3+ encrypt type
7. Immobilizer data tool: bugfix Fiat Linea 2007 95160
8. Immobilizer data tool: bugfix Mitsubishi Outlander 2009 24C16
9. Immobilizer data tool: bugfix for suzuki vitara 2006- 93C56
10. Bugfix for input chinese words in feedback window
11. Bugfix
===== J2534 V4.2.5 =====
1. Add Polish language support
===== Online Upate Tool V4.2.5 =====
1. Add Polish language support
===== Quick Start V4.2.5 =====
1. Bugfix
https://mega.nz/#!S1An0SxC!5l5_az319gR9yind4VPLQ-8iJWwMpNpjTUolixJA3-U
If you have interest to know more information about this product ,please enter this link:
http://www.eobdii.fr/wholesale/vvdi2-vvdi-pro-commander-key-programmer.html
SKP1000 tablet key programmer User Guide
1. Product description
1.1 Supported protocol:
SAE-J1850 PWM, SAE-J1850 VPW, KWP2000, ISO-9141, CANBUS, SINGLE CAN
1.2 Package Includes:
1* Main unit
1* touch pen
1* main cable
1* Honda 3pin adapter
1* Kia 20pin adapter
1* Hyundai / Kia 10pin adapter
1* Haima 7pin adapter
1* power adapter
1* TF card
1* TF card reader
1* USB cable
1* CD with user manual
2. Menu Instruction
2.10 Main menu basic functions
Car functions
Choose ” Car functions” to perform immobilizer, mileage adjustment, remote controller,
Oil/service Reset, throttle body adjustment, EPB, pin code calculation, personalized settings and special function
2.11 immobilizer function:
Clear key memory;
Program keys, proximity keys, smart key, flip keys;
Program after-market and OEM keys;
Read keys from immobilizer memory
New mechanical key number programming;
Vehicle identification key programming;
Reset ECU& Reset immobilizer;
Choose model: Hyundai, press “Confirm” to enter.
Choose “Smart card”, press “Yes” to enter.
Choose ” by car model”, press “Yes” to enter.
Choose “SONATA 8 (with card slot), press “Yes” to enter.
Choose “Smart card (with card slot), press “Yes” to enter.
Follow the tip to turn off ignition, press “Yes”
Follow the tip to open the door and close for one time, press “Yes”.
Choose smart card to match, press “Yes”
Follow the tip, insert the smart card into the slot, and you can hear alarm sound, turn off the ignition, press “Yes”.
Input the password
Check if the password is correct, press “Yes” to confirm.
The first smart card program successfully, and it will ask you if you program the next one, press “Yes” to confirm.
Insert the second smart card into the slot, you can hear the alarm sound, press “Yes”.
Program successfully, press “No” to back.
With two new smart card keys, you could start the car, if you need to add more keys, just repeat the above steps.
4. Firmware update
Before update firmware, please take out the TF card and insert it into the card reader, then plug into the computer USB port. Double click “My Computer”, find out ” local Disk (H:), right click to choose “Format”.
Tip: Tick on the “Quick format” and click “Start.
After complete format, go to the official site to download the update file, then copy and paste the file into the TF card, after finish, plug the TF card into the machine, power on the machine to the main interface.
Firstly choose “System firmware update”, press “Yes”, the procedure shown as below:
Update successfully shown as below.
Press “No” to back.
Choose ” Adapter firmware update”, after finish, reboot the machine to go on use SKP1000.
Done.
Any question, please contact your supplier.
Kess V2 V5.017 No Tokens Need Kess V2.23 Firmware V5.017 Add 140+ Protocols
Kess V2 V5.017 Highlight:
1. Multi-language support: English, German, Spanish, Italian, Portuguese, French.
2. Newest software: Ksuite V2.23
KESS V5.017 software is very easy to install, just click, Next Step, then it will work fine!
3. Latest and Best Firmware V5.017:
KESS V2 V5.017 supports more 140 types of vehicles and protocols than KESS V2 V4.036
KESS V2 V5.017 supports all protocols such as EDC17/k-line/DSG/DQ200 DQ250 DQ500 Gearbox/ST10 ….,No gray protocols anymore!
4. Online Version Kess V2 V5.017 is able to connect internet!!! Support online service!!!
5. 100% No Tokens Need for all vehicles, no tokens reset button, you can use Kess V5.017 for lifetime
6. Kess V2 Ksuite V2.23 Firmware V5.017 cover all major brands and protocols including Line, KAN, EDC17 and MED17 and for Ford J1850.
KESS V2 V5.017 can support cars/trucks/tractors/bikes! KESS V2 supports vehicles accroding to engine. So V5.017 KESS V2 can support new vehicles!
7. Works on Win XP / Win7 32bit, Win 8, etc.
8. Kess V2 V5.017 with a very affordable price, can read and write ECU via OBD2 port directly, no need to disassemble ECU from the car, easy to use.
En vente Digimaster 3 V1.8.1707.21 Digimaster III Original Odometer Correction Master
En vente Digimaster 3 V1.8.1707.21 Digimaster III Original Odometer Correction Master
New added BMW CAS+ CPU 1N35H read and write function after 2014 year.
Mise à jour: en ligne
Langue: English
Tokens: 300 times