Tag Archives: k518ise

Lonsdor K518ISE programs Volvo S40 key and Smart key

Lonsdor K518ISE programs Volvo S40 key and Smart key
Volvo S40 key programming with Lonsdor K518ISE

k518ise-volvo
1. Add key
Common key: add one piece
Smart key: Add one piece

2. Delete key
Key: delete the programmed key. Before deleting the key, please firstly select “Identify key ID” and record the ID info, during this process “The selected key ID will be deleted”.
Smart key: Delete all smart keys. If the key available is deleted, you could program it again.

3. Identify key ID
Key: the ID of key available can be identified, please record data.

4. Key unlock:
Key: Lonsdor K518ISE can detect and identify if the key is locked or not, if locked, K518ISE will unlock it. Note: K518ISE can unlock the key to the original car or the key with CEM security data.

Smart key: Lonsdor K518ISE can detect and identify if the key is locked, if yes it will unlock it. Note: only unlock the key of your car or corresponding cars’ key with CEM safe data.

As for “How to indentify smart and semi-smart key”, go for the last part.
1). Please dismantle the CEM (located in front of the passenger seat and the back of the storage box). There are 2 kinds of boxes, and the wiring is different, please follow the below diagram to wire and use K518ISE to read out 2 copies of data from left to right.
The wiring diagram of style-A box

wiring-diagram-for-style-a-1

wiring-diagram-for-style-a-2
The wiring diagram of style-B box ( double 1L15Y wiring diagram, the wiring position on the left is the same as that on the right)

wiring-diagram-for-style-b-1

wiring-diagram-for-style-b-2
2) After you read out the data, please provide your seller/ engineer with the 2 copies of data and K518ISE serial number, then wait for them to transfer it into special data. After you obtain the data, plug K518ISE to the computer and put the special data into the “customfile” folder for programming.

custom-file
3) Add key on Volvo S40
Key: to add key, please input the new key’s remote ID and remote code (choose 16bit/24bit).
Note: There are 2 types of key (P/L), please confirm the new key’ style and packaging  are the 100% same as that of the old key.

Smart key: just follow the instruction.

Key:
1) delete the key: before deleting the key, please firstly choose “Identify key ID” and record the ID info. During this process, “The selected key ID will be deleted”.
2) Please be sure to keep the new key box where printed the remote info that you will need to enter when adding key.
3) If the car has no KVM box (under the driver seat) it has a normal key, not remote.
4) During the key programming, you need to enter the remote ID and remote code (select 16 digits or 24digits).

Note: There are 2 types of key (P/L), please confirm the new key’ style and packaging are the 100% same as that of the old key.

P style:
The remote ID is 8 digits (No. 1 shown as below)
The remote code is 16 digits (NO.2 shown as below)

p-style-1

L-RFK style:
The remote ID is 8 digits (No. 1 shown as below)
The remote code is 16 digits (NO.2 shown as below)

L-RFK-style-1

L-RFK-style-2
Smart key:
1) Unlock: only unlock the key that K518ISE is working with or the key with CEM security data.
2) Delete the key that is programmed, after that the original key could be programmed again in the same car but if unlocked it won’t be used on another car.
3) S40 smart key programming needs no dismantling and reading KVM.
How to identify smart key and semi-smart key?
1) Smart key: comes with a coil, marked with “PK” on the packaging and no remote code (see the left picture below)
2) Semi-smart key: No coil, marked with “RFK” on the packaging and has remote code of 16 / 24 digits (see the right picture below)
identify-smart-key-1

How to identify if the car has smart key or semi-smart key?
1) If you can find a KVM box under the driver’s seat, it is a smart key, otherwise, it is semi-smart key.
2) The key handle is a plastic model key while the semi-smart key doesn’t have that.
identify-smart-key-2

identify-smart-key-3

Chip: 48 chip

Remote style: normal remote frequency: 433MHz; smart remote frequency: 433MHz

Key fob: Dedicated small key No. 24/38

Password requirement: dismantle and read CEM, backup security data, then program.

Remote generation:
Normal key: during key programming, you need to enter the remote ID and remote code, after the key is programmed successfully, then remote is generated.
Smart key: after the remote card is programmed successfully, the remote will be generated automatically.

OBD position: on the bottom left of steering wheel.

obd-position-1
Other information
1) car model

car-model-1
2) Key:
during the key programming, you need to input the remote ID and remote code (16 digits or 24digits).
There are 2 types of key (P/L), please confirm the new key’ style and packaging are the 100% same as that of the old key.

P style:
The remote ID is 8 digits (No. 1 shown as below)
The remote code is 16 digits (NO.2 shown as below)

p-style-2

L-RFK style:
The remote ID is 8 digits (No. 1 shown as below)
The remote code is 16 digits (NO.2 shown as below)

L-RFK-style-3

L-RFK-style-4

3) CEM box position (shown as below)

cem-box-position
4) Smart key:
You are advised to refer to the original key to select the new key. For example, the L-PK-434 key below is a remote key, which doesn’t have remote code of 16/24 digits.

smart-key-1

Lonsdor K518ISE for Porsche-Cayenne Test Report

Basically, there will be 4 parts in the whole help file: Function, Reference,Attention and Operation.
Function
1. Program smart key: to program smart card (please make dealer key first);
2. Make dealer key: use the backed up BIN data to make the non-dedicated
key to be dealer key.

Reference
Chip type: Dedicated smart card
Frequency: 315/433/434 frequency (please check the logo in the lower right of
the lid of the BCM box)
Key embryo no.: 31
Code requirement: Dismantle & read BCM to make dealer key
Key generation: Program smart key complete, remote will automatically generated
Under the steering wheel (BCM position):

lonsdor-k518ise-reference-1

BCM is located at the bottom left of the steering wheel, please note the
frequency type, basically there will be 315/433/434,
The following picture is for 434 frequency:

lonsdor-k518ise-reference-2
11-15 Cayenne Car Model

lonsdor-k518ise-cayenne-model-3

The car key

the-key-4
The induction keyhole

induction-keyhole-5

The mechanical knob key inserted into the induction keyhole

mechanical-nobe-key-6
Attention
1. All the keys need to learn, or it will not be able to start the vehicle, it isrecommended to learn the original car keys first,and then learn the new key,battery must be well installed.
2. The newly added key must be either the dealer key made via the car BCM data, or the key ordered back through the VIN code.
3. When learning key, it is required to insert the key into the induction keyhole,to learn a smart key, remove the machanical rotate key from the induction keyhole if any and then insert the smart key to program.

Operation
Step 1: Use the programmer to read and write BCM data and save it as bin file;
1. BCM is located in the lower left of the steering wheel, please pay attention to view the frequency type, usually there will be 315,433,434 frequency (below picture is for 434):

lonsdor-k518ise-operation-7
2. Read the BIN (D-FLASH / EEPROM) file with the programmer specifically for reading BCM. Please pay attention to the type here: namely 1L15Y 2M25J metal crystal, or 5M48H 1N35H ceramic crystal (red mark):

lonsdor-k518ise-operation-8

3. Please refer to the following picture to wire:

lonsdor-k518ise-operation-9
​Step 2: Copy the bin file into K518ISE: please use the USB cable to connect the K518ISE to the computer, open the device internal memory, find the folder “customfile” and copy the bin file into it (as shows belowl).
Note: bin file suffix “bin” must be lower case letters, directly put the file into the folder rather than create a new folder:

lonsdor-k518ise-operation-11
Step 3: Make dealer key
Step 4: Program smart key

Nouveau Programmeur de clés Nouveau Lonsdor K518ISE 2017

Nouveau Programmeur de clés Nouveau Lonsdor K518ISE 2017

I have tried the lonsdor this on 9 vehicles in the past two weeks all vehicles were lost all keys and here is what I find
2002 MK4 Golf – Unable to pull pin so I used different equipment to read pin and code key
2003 audi tt. failed to read pin so I used different equipment to read pin and code key
2006 MK5 Golf – pulled correct pin unable to code key.
2009 Corsa D – unable to read pin
2008 Suzuki Swift – communicated well but unable to code key without pin number. I used skp900 and key coded right away without asking for pin
2009 BMW E90 – Asked for Cas3+ to be updated this was a spare key not lost keys
2007 Fiat Punto grande – No communication
2006 Honda Accord coded key easily and quickly
2010 MK6 golf – need working key. does not give the option to code key from dump.
for more informations,please visit the following link
http://www.eobdii.fr/wholesale/lonsdor-k518ise-key-programmer-with-odometer-adjustment-for-all-makes.html

 

Lonsdor K518 Add New Key & Program Key All Key Lost for Toyota Corolla G chip

This post focus on the topic of how to use Lonsdor K518 add new key or program key all lost for Toyota Corolla G chip.

Add new key(2010 key chip)
1.Perform this function you need a master key.
Insert the key into the ignition,if the immo light does not light on,the key is master key.And if the immo light light on about 1 second and the off,the key is spare key.

2. Insert master key into the ignition,and turn it to “ON”,then waiting system communicating…
3. Insert the key you want to add(don’t need to turn the key)
4. Waiting for system programming,it will complete after a few seconds

Delete Keys(2010 chip)
Perform this function you need a master key.
Insert master key into the ignition,and turn it to “ON”,then waiting system communicating…
Insert the key you want to add(don’t need to turn the key)
Waiting for system programming,then deleting complete

Reset IMMO(for all key lost)
Note:After performing this operation,it no need to reprogram immo controller(2010 chip)

After reset the immo controller,it will restore to default status.
Turn off ignition,turn on ignition
System programming,pls follow guide to turn on or turn off the ignition…pull out key.
Please complete below step within 120s:
1 Program 2 master keys and 1 spare key
Insert first master key,turn ignition to on position and waiting for 5 seconds.
Insert second master key,turn ignition to on position and waiting for 4 seconds.
Insert thirdly spare key,turn ignition to on position and waiting for 5 seconds,then the immo light off,the programming complete.

Lonsdor K518ISE Key Programmer New Update Information

Lonsdor K518ISE Key Programmer New Update Information

Update time Nov.7 2017
2016-Ford kuga 49 Chip Smart key programming without Pin Code

lonsdor-ford-update

Update time Nov.10 2017
Rolls-Royce Wraith,Ghost Key programming

lonsdor-rolls-royce-update

Update time Nov.15 2017
K518 Free Update 2017 Buick GL8 smart key programming
Fiat Ottimo Toothless knob key programming via OBD

lonsdor-buick-gl8-update