Tacho Pro 2008 July PLUS Universal Mileage Change on Audi Model A4 Bosch model 2001 clip

Use this board and clip:

Prepare this Tacho Pro:
Tacho Pro 2008 July PLUS Universal

• Remove the cluster and open it.

• Pull off the needles for speed and rpm

• Look for the 8 pin chip 24C08.

• Connect the clip to Port 3.
• Put the clip on the chip 24C08 (red on pin 1).
• Select the menu Audi-A4-A4 24C08
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

Tacho Pro 2008 July PLUS Odometer Correction on BMW 5 series E39 high-IKE (instrument with 2 buttons)

This is mainly to showed you the Tacho Pro 2008 July PLUS Odometer Correction procedure on BMW 5 series E39 high-IKE (instrument with 2 buttons),since 11/1997, hardware 4,5,6, up to software 12.

Use this plug:

• Remove the cluster.
• Connect the cluster plug with the white and blue port and the Tacho Pro 2008 July Universal. Ensure that the red point on each plug faces pin 1 on the instrument’s port.
• Select the menu BMW-5er/7er-E38/E39 high-IKE
• The Tacho Universal shows you the hardware and software version of the instrument.
• Enter the new value.
• Verify the new value with OK..
• The Tacho Universal asks now OK or UNDO
• If you take a look at the display now, you can see the new value. If it is good, press OK, if not, you can undo everything with STOP.

Tacho Pro 2008 July PLUS Universal Dash Programmer UNLOCK on BMW Model 5 series E34 after 3/1989

Prepare: Tacho Pro 2008 July Plus Universal

Board for brown and blue code plug:

board for green code plug:

1. Remove the cluster.
2. Look on the rear for a small plastic cover. Under it you can see a brown, blue or green code plug. You have to break this cover to get the code plug out.
3. Take the code plug out.
4. Put the brown or blue code plug on port 1. The pins of the code plug are marked on the bottom in the plastic. Pin 1 of the code plug must be positioned on pin 1 of the board.
5. If the code plug is green, put it on the board “BMW green”. There you can also see the shape of the code plug Put the plug carefully on the socket.
6. Select the menu BMW-5er/7er-blue
or BMW-5er/7er-brown
or BMW 5er/7er-green
7. The Tacho Pro 2008 Universal shows you the old value.
8. Select the menu Adjust KM.
9. Enter the new value.
10. Verify the new value with OK.

Brown code plug:

Tacho Pro 2008 July PLUS Universal odometer correction on Ford Focus Step by Step

Tacho Pro 2008 July PLUS Universal is one French favorite device to do mileage correction. It can do multi-brand cars than the other tool. See the procedure to do on Ford Focus bellow:

Use the Scorpio plug:

26pin white port
• Pin 2      GND(-)          black
• Pin 9      RX (Data)     blue
• Pin 11   TX (Data)     yellow
• Pin 14   12V (+)          red
• Pin 16   12V (+)         red

Processor version 1:
• Connect Pin 1 ( left side down) and pin 2 (right from pin 1), or connect black to test point 3 (TP3).

Processor version 2:
• Connect pin 1 (middle upside) and pin 2 (left beside pin 1), or connect black to testpoint 46 (TP46).

• Remove the cluster and open it.
• Connect the cables as shown in the picture.
• Select the menu Ford-Focus
• The Tacho Pro 2008 July PLUS Universal shows you the old value.
• Enter the new value.
• Verify the new value with OK.

How to do Model Audi A3/S3 VDO model 2000 cluster plug with Tacho Pro 2008 July PLUS Universal?

To recognize model 2000, take a look at the clock. If it is electronic, it is model 2000, if it is mechanic it is an older model.
Use this plug:

Tacho Pro 2008 July PLUS Procedure:
1. Remove the cluster.
2. Connect the blue and the green plug to the instrument.
3. Select the menu Audi-A3-A3 2000-Diagnosis 2000.
4. The Tacho Pro 2008 July PLUS shows you the old value.
5. Enter the new value.
6. Verify the new value with OK.

Note:
If the displayed value is not correct, you can continue programming, most time it works anyway.
You cannot destroy anything. If you cannot change the value this way, you have to program by clip.

Tacho Pro 2008 July PLUS Universal Dash Programmer Odometer Correction on Citroen Model Xsara

Preparation:
Tacho Pro 2008 July PLUS Universal Dash Programmer
Use this board and clip:

Operation Steps:

• Remove the cluster and open it.
• Remove the motors carefully from the circuit board. Do not pull off the needles!!!
• Look for the 8 pin chip 93C46.
• Look for the silver chrystal and join its contacts.
• Connect the clip to Port 1.
• Put the clip on the chip 93C46 (red on pin 1).
• Select the menu: Citroen-Xsara
• The Tacho Universal shows you the old value.
• Select the menu Adjust KM.
• Enter the new value.
• Verify the new value with OK.

Tacho Pro 2008 July PLUS Universal on BMW Model 3 series E36 Compact up to Software 7

Preparation
Tacho Pro 2008 July PLUS Universal
Plug like the picture bellow:

Procedure to change mileage on BMW Model 3 series:
1) Remove the cluster.
2) Connect the plug with the blue port and put the 3 pin plug in the 4 pin port left down on the instrument. Put this plug in as it is easy. If it is hart to position, it is upside down!
3) Select the menu BMW – Z3/COMPACT – Diagnosis.
4) The Tacho Universal does not show you the old value.
5) Enter the new value.
6) Verify the new value with OK.