Category Archives: Lexia-3

How to program Peugeot 307 key with Lexia 3?

How to program Peugeot 307 key with Lexia 3?

Prepared tool you will need:

1.Lexia-3 lexia3 V48 Citroen/Peugeot Diagnostic PP2000 V25 with Diagbox V7.53 Software
2.All the vehicles keys.
3.A laptop that contains Lexia3/ PP2000 software.
4.Confidential code

Procedure of how to program Peugeot 307 key:

Step 1. Open up Peugeot PP2000 Diagbox software, select vehicle model “307” and click “OK” button at the bottom right. The PP2000 diagnostic software will start searching for the 307 car.

Step 2. Hook up Lexia3 PP2000 interface to the laptop and the OBD port of the car. Turn on the ignition. PP2000 will build connection with the car within a few seconds.

Step 3. Confirm vehicle information, including its VIN code, motor, chassis number and body. If the vehicle info is right, click “OK” to continue.

Step 4. Select application as “Peugeot Planet 2000”.

lexia3-pp2000-peugeot-307-key-1

Step 5. Select “Test by ECU”.

Step 6. Select “Built-in systems interface”.

Step 7. Select “Learning” to get car key information.

Step 8. Select “Programming of keys”.

lexia3-pp2000-peugeot-307-key-2

Step 9. Follow the prompts in picture below.

lexia3-pp2000-peugeot-307-key-3

Step 10. A few seconds later you will get this window. Enter the Confidential code located on your confidential card. Verification of the confidential code will then start. If the confidential code is correct, the built-in system interface will ready for programming the key

Step 11. Enter the number of keys that you want to learn. At most 5 keys can be programmed. Here I will replace only one key.

Step 12. Switch off the ignition.
Step 13. Use the blank key to switch on the ignition positive
Step 14. You will get a message “Key programmed. Switch off the ignition and take out the key” when a new key is successfully programmed.

lexia3-pp2000-peugeot-307-key-4

How to connect Lexia 3 V48 xs Evolution PP2000 to Citroen Cars?

How to connect Lexia 3 V48 xs Evolution PP2000 to Citroen Cars?

1. Look under the Citroen driver-side dashboard for the diagnostic trouble code (DTC) connection port. It is black, rectangular-shaped and roughly one inch wide by a 1/4-inch tall. It should have a small cap on it to prevent dirt from entering the connector. Quite often the cap will have the letters “DTC” embossed on it.

2. Remove the cover from the connection port and move the cover off to the side. Lexia-3 Lexia 3 V48 xs Evolution PP2000 should be attached to the port by a thin strand of plastic to prevent the cap from being lost. Plug in your Lexia 3 PP2000’s OBD-ii cable to the connection port.

3. Turn on your Lexia 3 PP2000 diagnostic toolWrite the codes down from the Lexia 3 PP2000 Peugeot Citroen Diagnostic tool, once you have them, as you will need to refer to them during the troubleshooting process that is easy to contact and use it.

lexia-3-diagnostic-pp2000-on-citroen-connect

LEXIA 3 PP2000 Works well on Citroen C5:

lexia-3-diagnostic-pp2000-on-citroen-1lexia-3-diagnostic-pp2000-on-citroen-2

How to deal with Citroen C3 climate and radiator fan error?

How to deal with Citroen C3 climate and radiator fan error?

I want to share my experience troubleshoot climate and radiator fan issue with more people.

I have 2004 C3 HDI, with smart fan 1253h3, has ABS with no esp and automatic climate. When I switch climate on or heat bar 3 dash warms and beeps 3 times and all the heat lights come on. I noticed that if engine warning light on everything is ok when engine warning light turn off on the dashboard fan not cuts in and the problem comes back. I changed engine heat sensor, thermostat, controlled all wiring (can bus wiring, fan power cables), changed relay. But nothing solved the problem. Then I went to C3 forum for help, and a member told me to use Lexia-3 to pull up any error codes before changing parts and it can help guide to the point of the problem.

I bought a Lexia-3 scanner from a Chinese shop, hooked it up my C3 this morning and got a P0485 code. Below is a screenshot of Lexia-3 software (Diagbox) .

diagbox-softwarediagbox-software-1diagbox-software-2

On slow speed actuator it says faulty actuator. But sometimes fan cuts in. An interesting alternative description for P0485 is Cooling Fan Power/Ground Circuit Malfunction. It might be a fan or an ECU, I am not sure from a P code. But it is easier to try a new fan than try a new ECU. So I replaced the fan, and the clear the climate control problem is fixed.

Lexia-3 lexia3 V48 Citroen/Peugeot Diagnostic PP2000 V25 with Diagbox V7.53 Problem Solved!

Lexia-3 lexia3 V48 Citroen/Peugeot Diagnostic PP2000 V25 with Diagbox V7.53 Problem Solved!

Question: I need your help, I already bought you 2 Lexia-3 lexia3 V48 Citroen/Peugeot Diagnostic PP2000 V25 interfaces before and I never had any problems until now. But with the one you just send me I can not make it work. The interface is well recognized at usb from windows, but it is not detected by the software, whether Lexia, or PP2000 diagbox, none detects the interface. When i plug the usb on computers, the green led light on 2 seconds and light off after. I watched with PSA Checker interface, I get nothing, except the message “Init KO”. So I’m stuck, I admit not knowing what to do, I tried on multiple computers, I do not get better. Please see the picture: lexia-3-citroen-peugeot-diagnostic-error-1

lexia-3-citroen-peugeot-diagnostic-error-2lexia-3-citroen-peugeot-diagnostic-error-3

Answer: According to your description, the Lexia-3 interface PCB board may have problem. Please unsolder the chip on pcb like the picture bellow  in the red circle and solder the new one. I will send you the new chip for you to use it. Any question, contact: sales@eobdii.fr.

lexia-3-chips

Lexia-3 Lexia3 V48 PP2000 V25 Diagnostic Tool for Peugeot/Citroen With Diagbox V7.57 Peugeot 307 Supported!

Lexia-3 Lexia3 V48 PP2000 V25 Diagnostic Tool for Peugeot/Citroen With Diagbox V7.57 Peugeot 307 Supported!

Why to choose Lexia-3 Lexia3 V48 PP2000 V25 Diagnostic Tool?

1. This is the cheapest Lexia-3 that can support Peugeot 307 car model.
2. Multi-language Supported: English/ German/ French/ Japanese/ Russian/ Spanish/ Portuguese/ Swedish/ Turkish/ Dutch/ Polish/ Italian/ Hungary/ Greek/ Czech
3. Lexia-3 relays are 12pcs, which are 4.5V, it is more stable.
4. Lexia-3 PCB edge is golden with original full chips. Double PCB has 7pcs optocouplers, which are 100% original and new.
5. Lexia-3 main cable comes with LED light, better for night work!

See the Lexia-3 PCB board picture:

lexia-3-pp2000-diagnostic-tool-with-diagbox-pcb-board

Lexia-3 Diagbox Software View:

lexia-3-pp2000-diagnostic-tool-with-diagbox-software-1

lexia-3-pp2000-diagnostic-tool-with-diagbox-software-2

lexia-3-pp2000-diagnostic-tool-with-diagbox-software-3

How to disable Mitsubishi TPMS light with Lexia3 V48 xs Evolution Diagnostic?

How to disable Mitsubishi TPMS light with Lexia3 V48 xs Evolution Diagnostic?

I have a 2010 EVO X and like many homeowners, I looked for a way to disable the “Service TPMS” annoying light for a long time. The good news is I finally found a thread of “forums” Mitsubishi and got the light disabilities. Here is how I did. Lexia-3 a code reader is required in this process.

Things you will need:

A: Lexia-3 Lexia3 V48 xs Evolution Citroen/Peugeot Diagnostic PP2000 V25 with Diagbox V7.57 Software– (The Lexia 3 I use is V46, the latest version is lexias 3 V48. If you are interested: http://www.eobdii.fr/wholesale/lexia-citroen-peugeot-diagnostic-pp2000-with-diagbox-software.html.)
B: A laptop Windows XP or laptop with Win XP Mode 7/8

Follow the procedure to do:

1) Install the software Lexia 3 first:
– Then navigate all the way in the PP2000 10A & lexia v46 Dir and find update_lexia_346.22.exe
– Run this update V46 pointing to the same location you selected from the V45 install

2) Connect Lexia 3 interface to the OBD port in my EVO X.
– Upgrading of V46 will revert to this point, simulating a web update.
– Make activation and make sure that you are using LEXIA-346 since you’re up to date
You just activated this way, otherwise you must re after the upgrade.

3) Select “C-Crosser”, “Lexia”, “Diagnosis” and “test function”. Choose the category based on your selection, there take SUV as an example and come to the ECU list.
– You will see the ETACS interface also called “BSI”.
– Select BSI – Configuration – Manual configuration then there will be two options for the configuration of the vehicle and customer choice.
– Select the client options, select “repair”.

4) Enter the menu “ETACS-SUV default programming.” Select “Under the inflection.” TPMS is included the option. The current state is present (ON).
5) The system is currently paralyzing the state of inflation.
6) The system automatically disables inflaction parameters. The status now turns to “away” (OFF)
7) the TPMS light is off.

Here are some photos:

lexia-3-pp2000-xs-evolution-1lexia-3-pp2000-xs-evolution-2lexia-3-pp2000-xs-evolution-3lexia-3-pp2000-xs-evolution-4lexia-3-pp2000-xs-evolution-5lexia-3-pp2000-xs-evolution-7lexia-3-pp2000-xs-evolution-6